PDA

View Full Version : My first Tribal and a quick question

gremlin75
03-02-2009, 01:09 PM
First off Thanks to Edwin for allowing me to register here.

So I have always like the flusters and finally after thinking about getting one for years I finally did it. I picked up a Tribal Fluster with a single trigger and LPRC

http://img.photobucket.com/albums/v448/gremlin75/TribalFluster.jpg
http://img.photobucket.com/albums/v448/gremlin75/TribalFlusterSide.jpg

Im probably going to end up putting an 07 Chaos board in it since they are so darn cheap now a days.

My question is, with the 07 chaos can I just use a bko/b2k wiring harness or will I have to mod the stock harness. Also Im not planning on adding eyes if that matters with the harness.

later
gremlin
~kaos~
03-03-2009, 01:43 AM
Greetings and welcome to the TOG... sorry for the need for manual activation but it keeps the forum much 'cleaner'.
For your Chaos install you'll find using the ICD wiring harness easier than modding the stock Tribal harness. However there is another option if Edwin is still making custom harnesses for them.
gremlin75
03-03-2009, 02:23 AM
Greetings and welcome to the TOG... sorry for the need for manual activation but it keeps the forum much 'cleaner'.
For your Chaos install you'll find using the ICD wiring harness easier than modding the stock Tribal harness. However there is another option if Edwin is still making custom harnesses for them.

No problem on the registration, I just bugged edwin till he turned the registration back on :goofball:

I figured that since the 07 chaos boards are only $60 now Id just spend the few extra bucks on that and get that and a bko harness instead of getting the fury chip.

I have a feeling this is going to turn into another un-needed project gun for me........but in the end un-needed projects are so much fun :woot5:

P.S. Good god this place has a ton of smilies! :NahNah:

later
gremlin
Spitlebug
03-03-2009, 11:54 AM
A BKO harness is a good way of going about putting a Chaos board in your Tribal. Just remember that you may need to splice some wire in there to connect the LED and the on/off switch. :2thumbup:
gremlin75
03-03-2009, 02:54 PM
A BKO harness is a good way of going about putting a Chaos board in your Tribal. Just remember that you may need to splice some wire in there to connect the LED and the on/off switch. :2thumbup:

Splicing wires us a ok with me, cause you can suck at soldering and and still get the job done (and boy do I suck at soldering!) LOL :D
~kaos~
03-05-2009, 01:05 AM
I'm an absolute Rembrandt when it comes to soldering, that's probably why women find me irresistible..... :naughtys:
gremlin75
03-05-2009, 01:30 AM
I'm an absolute Rembrandt when it comes to soldering, that's probably why women find me irresistible..... :naughtys:

LOL, Im more of a butcher when it come to soldering :Help:

I was lucky enough to get the fluster in today before I headed to the field. Gun shot great and t was fun to shoot a single trigger again. Had a small leak down the barrel but noting huge. Looks like it may need a new cup seal as some oil didnt help the matter. Anyone know where I could get a new one? Or can I use a cup seal from another gun??
Spitlebug
03-05-2009, 10:20 AM
LOL, Im more of a butcher when it come to soldering :Help:

I was lucky enough to get the fluster in today before I headed to the field. Gun shot great and t was fun to shoot a single trigger again. Had a small leak down the barrel but noting huge. Looks like it may need a new cup seal as some oil didnt help the matter. Anyone know where I could get a new one? Or can I use a cup seal from another gun??

Bushmaster valves work if you knock out the stop pin in the body. The stock valves look a lot like 'Cocker valves and as such they put that stop pin in there... :doh: